As many of you know, I gave birth to my son on March 6th 2015. He is my first child, and after two years of trying to conceive, having 2 miscarriages, we were finally blessed with our son CJ.
My pregnancy was normal by all accounts, normal amount of morning sickness, weight gain, blood pressure etc..., so I was expecting a normal as possible birth as well, but unfortunately I got anything but.
In my doctors appointments in the weeks leading to my due date the midwife had indicated that CJ was "sunny side up" meaning that normally babies are born with their faces toward your back, CJ was turned so that his face was turned toward the front. I tried to research this information, and discussed it with my doula, but was really not well informed or prepared for what that would ultimately mean.
My last doctors appointment was 3 days after my official "due date" but I wasn't worried, I knew from lots of research that about 70% of first time births occur after the due date, he would come when he was ready. The midwife asked to do a cervical check, which up until that point I had declined, but I allowed it at this last appoint. I was dilated to a 2, no effacement. She asked if she could rupture my membranes, so which I declined. The cervical check felt very uncomfortable, and I remember wondering if she had done it anyways, but my doula later told me that she didn't - it would have been much worse then I described.
It was a Wednesday for my doctors appointment, and I had taken the day off so that I could rest and recuperate but had planned to go to work the remainder of the week. I went to bed and woke up at 3AM to strong contractions. I labored with intermittent contractions until 6:00AM before my husband called my doula to come assist. I had planned to labor at home until I was much farther along in my labor, near the point of transition and then making my way to the hospital.
I tried to relax as much as possible, took a shower and tried to eat, but my contraction pain was unbearable, having what I now know as "back labor" due to my son being turned the wrong way - his skull was pressing down on my spine with each contraction causing a very sharp shooting pain in my back with each contraction.
My doula arrived at 8:00am. She had also suspected that CJ was turned the wrong way - and had suggested some positions of laboring to encourage him to roll over into the proper position, we attempted 3-4 positions of laboring until about 3:00pm that day, as my labor slowly progressed. I got into a situation where I was starting to having regular 4 minute interval contractions and the pain was becoming very intense, so I was hoping that we were close.
We arrived at the hospital only for me to discover to my dismay that I was only dilated to a 3. I persevered and continued to labor, unassisted in both the tub and in a standing position until about 7:00pm that evening, where I was finally convinced to use Pitocin and receive an epidural. Coming to terms with the fact that I would not be having an unmedicated birth was soul crushing for me, I had intended to give birth naturally and tired to mentally prepare myself for other possibilities, but in the end I was crushed when the decision to use medication was reached, I felt like a failure and I felt defeated, which I think also affected the remainder of my labor and delivery, looking back on it now.
The Pitocin and epidural slowed my labor process down even more, and I didn't reach 10cm until about 5:00pm the following day, the epidural kept wearing off, and I was experiencing something known as "dead spots" where spots of my abdomen had complete feeling, while other spots did not - and while continuing to have back labor - was not providing much relief from the pain at all, they ended up redoing my epidural twice. By this point I had labored for about 41 hours at that point, I was beyond exhausted when it finally came time to push.
I pushed for a full hour, every contraction, without taking a break, and he barely crowned, he was stuck. I started to experience a rapid drop in blood oxygen levels from exertion, and I started to spike a fever. The baby's heart rate began to rise rapidly as well, and so they told me I would need to have an emergency C-section at that point.
When a baby becomes stressed during labor they will actually poop of some of the meconium in their systems, and the doctors told me that this had happened during my labor at some point, and combined with my fever they were worried that the baby was developing an infection. I did not hesitate to agree to the C-section at this point, I was barely conscious and I was not in my right mind at all. I can remember when they told me that I needed to consent to the C-Section I just broke down and began balling with my husband, it felt like forever, but we just cried in each others arms; relieved, scared, defeated, worried - every emotion was going through my mind.
I can distinctly remember thinking that I was too tired to stay awake for the surgery and being worried that I would miss the birth of my son from my overwhelming exhaustion. The doctors had to change my epidural medication to something stronger - for fear that I would feel the surgery take place - something that at the time I couldn't care less about - but in retrospect, should have been terrified given the dead spots I had experienced earlier.
The prep and surgery took less than 30 minutes and my son was born at 7:27PM. When my son was handed to me I had to focus all of my energy on not dropping him, and I had to hand him back to my husband because I was so scared I would. I kept slipping in and out of consciousness and tried to rest as much as possible while they stitched me back up.
In the recovery room I wanted to do skin to skin as quickly as possible, so they striped him naked and laid him on my chest, where he proceeded to poop out a large quantity of that tar like meconium all over me, but I didn't mind at all. I finally had my perfect little miracle and I knew that we would be alright after that. We both lost our fevers, and while I had to remain on oxygen for the next 24 hours to get my blood oxygen levels back to normal, everything else worked out fine.
This also marks that start of my continued (still one year later) deficit of sleep, for which I feel I will never fully recover. We ended up leavng the hospital a day early because the nursing staff would not stop waking us up to mess with us, and I wasn't getting any recuperating rest during our stay. My son is a horrible sleeper as it is - and I am just now starting to get consistent full nights sleep one year later.
I've created this blog as a place to record my thoughts, experiments and successes all in one place. I hope you enjoy reading about my crazy life, and thanks for stopping by!
Showing posts with label home. Show all posts
Showing posts with label home. Show all posts
Sunday, December 9, 2018
Wednesday, October 16, 2013
Easing back into painting
Long ago I used to paint, like 10 years ago, I would paint on my tabletop easel late at night, and create these cute Bob Ross style landscape paintings. They are hanging all over my parents house, literally, they are hanging ALL OVER my parents house. I love it, it think it's cool to see my progression and skills increase over time, but alas, I soon grew tired of this style painting, and the enormous expense involved with oil painting.
Now that I own my own home, and am at an ever desperate attempt to decorate and fill the vast empty walls my home contains, I've began thinking about painting again. I would love to have original unique artwork instead of your typical reproduction prints you pick up in the home department at Target. I also like the idea of creating something that truly complements the colors in your home.
So, here we are, I found myself at hobby lobby picking up a few canvases and some acrylic paints this time. My husband bought me a free standing easel, and we got a few new brushes. I've decided to try my hand at a more abstract style painting, I still love the idea of painting landscapes, but I feel the desire to be more open in my interpretation of what a landscape is. My first painting was a lose interpretation of two doves on a wire, something my hunting husband loved, and the colors compliment our master bedroom, so it's a win-win.
I used acrylics and it is a highly textured canvas, using a texture medium. Not too bad for a 10 year hiatus if I do say so myself! More to come I'm sure!
Wednesday, September 4, 2013
Subtle Wall Stripe
Subtle Wall Stripe

Directions:
Step 1 Prep Work:
As with all paint projects, prep work is key. First paint a base coat on the walls; for stripes that's really important because the base coat will be one of the stripes. Use a flat paint that is exactly the same color as the stripe to be painted on. It's also important that the base coat dry for 48 hours before you start to work on the stripes.
Step 2: Measure and Mark the Walls
After the base coat is completely dry, begin measuring and marking the walls for the stripes.
Measure the wall, starting in the corner that's least seen.
Next, divide the wall. Stripes should be between 4" and 12" wide. (I did 12" stripes because I have a HUGE wall and anything smaller would be too busy) Place the first strip of tape in that obscure corner where you began measuring.
Place the end dot on the tape you've already applied to the wall and press the strip to the wall.

Next, if you have one I highly suggest using a laser level to shoot a beam onto the second dot. I did not have one so I make several marks on the wall from top to bottom and placed the tape very carefully along each line to create a straight tape line.

Step 3: Press the Strip of Tape to the Wall
Tip: Remember that because you will be painting only every other stripe, you'll need to tape out the pattern so that every other stripe is outlined by the tape. Make sure to tape outside the chalk line; fresh paint will cover up the lines.

Tip: You can also make the lines with a chalk line. Use blue chalk because red or yellow is a permanent color.
I used both blue painters tape and green frog tape, I ran out of the frog tape very quickly, so I had to make sure to maintain the same measurements using a thinner tape. Basically what I did was split my wall in half. It is 280" and 140" would be dead center.
Since I wanted my stripes to be 12" wide I measured 6 inches on either side of center and then created my first stripe. The tape for the glossy stripe (the ones we will be painting over the matte wall) had the tape lines exactly 12" apart, so the other stripe (the matte stripe) would have the tape one both sides inside the 12" perimeter, so that the glossy stripes would all be 12" exactly, and the leftover tape went on the inside of the matte stripes since I was not painting them. Once we remove the tape both stripes will be an even 12 inches.

Step 4: Burnish the Wall
Taking a roller that is smaller then the diameter of your stripes and a small paint brush. Using the paint brush I did the ceiling and above my trim and using the roller I filled in the center. Make sure that you get the gloss color over the paint about halfway, so that the paint lines are very clear when you peel the tape off.

Step 7: Remove the Tape
Remove the tape once you've painted the wall, angling away from the freshly painted area as you pull. I gave it 15 minutes before I removed the tape, giving me time to paint 1 stripe before removing the tape from the previous stripe. You DO NOT want to leave the tape on too long, I've seen vinyl paint peel after drying and I would hate for it to peel after all this work!

The tape and paint technique worked amazingly, it created crisp and even lines and since the color is the same, one stripe being glossy and the other matte, it created a classy and elegant wall that is subtle and gorgeous!.

Progress as I move down the wall!

All finished!

Starting to put my frames back up and my furniture back!

Directions:
Step 1 Prep Work:
As with all paint projects, prep work is key. First paint a base coat on the walls; for stripes that's really important because the base coat will be one of the stripes. Use a flat paint that is exactly the same color as the stripe to be painted on. It's also important that the base coat dry for 48 hours before you start to work on the stripes.
Step 2: Measure and Mark the Walls
After the base coat is completely dry, begin measuring and marking the walls for the stripes.
Measure the wall, starting in the corner that's least seen.
Next, divide the wall. Stripes should be between 4" and 12" wide. (I did 12" stripes because I have a HUGE wall and anything smaller would be too busy) Place the first strip of tape in that obscure corner where you began measuring.
Place the end dot on the tape you've already applied to the wall and press the strip to the wall.

Next, if you have one I highly suggest using a laser level to shoot a beam onto the second dot. I did not have one so I make several marks on the wall from top to bottom and placed the tape very carefully along each line to create a straight tape line.

Step 3: Press the Strip of Tape to the Wall
Tip: Remember that because you will be painting only every other stripe, you'll need to tape out the pattern so that every other stripe is outlined by the tape. Make sure to tape outside the chalk line; fresh paint will cover up the lines.

Tip: You can also make the lines with a chalk line. Use blue chalk because red or yellow is a permanent color.
I used both blue painters tape and green frog tape, I ran out of the frog tape very quickly, so I had to make sure to maintain the same measurements using a thinner tape. Basically what I did was split my wall in half. It is 280" and 140" would be dead center.
Since I wanted my stripes to be 12" wide I measured 6 inches on either side of center and then created my first stripe. The tape for the glossy stripe (the ones we will be painting over the matte wall) had the tape lines exactly 12" apart, so the other stripe (the matte stripe) would have the tape one both sides inside the 12" perimeter, so that the glossy stripes would all be 12" exactly, and the leftover tape went on the inside of the matte stripes since I was not painting them. Once we remove the tape both stripes will be an even 12 inches.

Step 4: Burnish the Wall
These next two steps are the most important prep work you can do when painting stripes on a wall. If you do not complete these steps you won't get nice crisp paint lines on your wall.
Burnish wall with a credit card to seal the tape edges so no paint seeps underneath the tape.

Step 5: Paint Over the Tape
Paint over the tape line with the base paint (the matte paint), making sure to only paint about half the paint line, otherwise when you pull the paint off you will see a distinct line one both sides where the tape was. One coat should be enough. Make sure there are no gaps between the wall and the tape, and if there are burnish the tape again and fill the gap with the base paint to form a seal.

Allow the paint to dry for 1 hour. Basically by the time I was done painting all the stripes I could start back on the other side of the wall.
Step 6: Paint the stripes
Burnish wall with a credit card to seal the tape edges so no paint seeps underneath the tape.

Step 5: Paint Over the Tape
Paint over the tape line with the base paint (the matte paint), making sure to only paint about half the paint line, otherwise when you pull the paint off you will see a distinct line one both sides where the tape was. One coat should be enough. Make sure there are no gaps between the wall and the tape, and if there are burnish the tape again and fill the gap with the base paint to form a seal.

Allow the paint to dry for 1 hour. Basically by the time I was done painting all the stripes I could start back on the other side of the wall.
Step 6: Paint the stripes
Taking a roller that is smaller then the diameter of your stripes and a small paint brush. Using the paint brush I did the ceiling and above my trim and using the roller I filled in the center. Make sure that you get the gloss color over the paint about halfway, so that the paint lines are very clear when you peel the tape off.

Step 7: Remove the Tape
Remove the tape once you've painted the wall, angling away from the freshly painted area as you pull. I gave it 15 minutes before I removed the tape, giving me time to paint 1 stripe before removing the tape from the previous stripe. You DO NOT want to leave the tape on too long, I've seen vinyl paint peel after drying and I would hate for it to peel after all this work!

The tape and paint technique worked amazingly, it created crisp and even lines and since the color is the same, one stripe being glossy and the other matte, it created a classy and elegant wall that is subtle and gorgeous!.

Progress as I move down the wall!

All finished!

Starting to put my frames back up and my furniture back!

Subscribe to:
Posts (Atom)


